We're adding six new translucent PLA filament colors to Standard PLA+: Translucent Cyan, Translucent Magenta, Translucent Yellow, Translucent White, Translucent Black and Transparent Smoke Black. Together they make a CMYKW set for color mixing and FullSpectrum printing, and they'll work on any printer that can do it: the Bambu Lab H3C and H2C, a Prusa INDX or XL, a Snapmaker U1, a Voron with a toolchanger or MMU, or anything else that can switch between filaments in a print. Like the rest of Standard PLA+, they're made here in Fargo, North Dakota, from 100% virgin Ingeo 4043D, and they're $22.95 a spool.

If you listened to episode 20 of the 3D-Fueled Show, you knew this was coming. We launched a translucent CMYKW set in Pro PCTG back in July. The Snapmaker U1, Bambu Lab H2C and Prusa INDX are what got us moving on a PLA+ version. Then the H3C came out, the latest, hottest printer that can take advantage of these colors, with Bambu's color mixing built around a five-color CMYKW palette in PLA. None of that ties these colors to one brand. A lot of color mixing work is decorative, display pieces and figures and signs, and for those parts PLA+ is easier to print and costs less than Pro PCTG.
The six colors and their TD values
Every color has a measured TD (transmission distance) value on its product page. A higher TD means light travels through more layers before the color goes opaque, which is what lets thin layers blend.

| Color | TD | Hex | Pro PCTG TD |
|---|---|---|---|
| Translucent Cyan | 4.7 | #0091CD | 5.4 |
| Translucent Magenta | 4.9 | #B42562 | 7.1 |
| Translucent Yellow | 6.1 | #FCDC1D | 6.9 |
| Translucent White | 6.0 | #E3DDDB | 7.5 |
| Translucent Black | 1.2 | #292524 | 1.2 |
| Transparent Smoke Black | 13.0 | #1D2229 | 16.0 |
You'll notice the PLA+ numbers run a little lower than the Pro PCTG versions. PCTG is about the best material there is for clarity, and PLA just isn't quite as clear. That said, the translucency carries over. We printed this Chromatic Owl entirely in the CMYKW Standard PLA+ set, and the layers blend instead of showing as stripes. The callouts show the five colors straight from the spool and the mixes the slicer built from them.

Why translucent filament matters for color mixing
Color mixing, whether it's FullSpectrum, Bambu Studio's color mixing or another slicer's version of it, makes new colors by stacking very thin layers of different filaments. Alternate cyan and yellow layers and your eye reads green. Change the ratio of those layers and you get a different green, all from the same two spools.
The catch is opacity. With a fully opaque filament, the top layer hides whatever is under it, so you see bands of color instead of a blend. A translucent filament lets light pass down through a few layers and back out again, and that's where the mixing actually happens. Translucent White matters more than people expect here. An opaque white washes everything out fast, while a translucent white lets you build pastels and lighter shades gradually.
If you want the longer version of how this works, our Pro PCTG color mixing post goes through it with test prints.
Two blacks, and when to use each
We made two blacks on purpose, because they do very different jobs.
Translucent Black has a TD of 1.2, so it darkens a color stack quickly. It's the one for deep shadows, outlines and strong contrast. Because it takes over fast, I'd use it more sparingly in a mix than the other four colors.
Transparent Smoke Black sits at the other end at a TD of 13.0. You can see through it, so it adds a dark tint without blocking what's underneath. It's good for gradual shadow transitions in a mix, and printed on its own it gives you smoked covers, lamp shades and parts where you want to see the inside.
Which printers can use them
If your printer can swap filaments mid-print and your slicer can build mixed colors from thin layers, these will work. The filament doesn't care what brand of printer it's in. What changes from printer to printer is how much purge waste you get and how long the print takes.
- Toolchangers and multi-nozzle printers like the Prusa INDX and XL, Snapmaker U1, Bambu Lab H3C and H2C, and Voron toolchanger builds are the best fit. Each color has its own nozzle or tool, so there's little to no purging between colors.
- Dual-nozzle printers like the Bambu Lab H2D cut purging down a lot compared to a single nozzle.
- Single-nozzle printers with a multi-material unit, like a Bambu AMS, Prusa MMU3, Creality CFS or a Voron with an MMU, work too. Expect a lot more purge waste and longer prints, since the nozzle has to flush every color change.
On the software side, set each color up as a custom filament with its hex code from the table above. FullSpectrum, Bambu Studio and other slicers that support color mixing build the mixed colors from there.
Printing them on the Bambu Lab H3C
The H3C ships with eight PrintTools for 1.75 mm filament plus one for 2.85 mm TPU. Load the five CMYKW colors and you still have three tools free for other filaments, or two if you add Transparent Smoke Black. Because each color has its own tool, you skip the purge you'd get changing colors on a single nozzle.
Our 1 kg spools are sized to fit AMS-style systems, and we developed these colors with nozzle- and tool-switching printers in mind. Full dimensions for every spool we use are in our spool sizes and weights article.
A few setup notes:
- Bambu Studio's color mixing presets are built around Bambu's own PLA Palette set. Ours work as custom filaments: add each one, enter its hex code from the table above, and Studio builds the mixed colors from there.
- On any printer, the on-screen mix is a prediction, so I'd print a small swatch palette before committing to a big model.
- Print at 220-250 °C. Start around 240 °C on a fast printer like the H3C. A generic 200-215 °C PLA profile is too cold for our PLA+.
- Bed at 60 °C on the Textured PEI Plate that ships with the H3C, part fan on.
- H3C profiles for Standard PLA+ are coming. In the meantime, we have Standard PLA+ print profiles for a wide range of 3D printers, including the Bambu Lab H2C and the Snapmaker U1.
Not just for color mixing
Each of these colors prints fine as a single color. Translucent Yellow and Translucent Cyan make good light covers and vase-mode lamp shades, and the hex and TD values are useful for HueForge and other filament painting work. They're all in our HueForge color library (right-click, save as).
Price, and getting the whole set
All six are 1 kg spools of 1.75 mm filament at $22.95 each. Buy all six and you hit our 5-spool quantity discount, so 5% comes off automatically at checkout and the set comes in just under $131. That's also over $99, so it ships free in the contiguous 48 states. Mix in other colors or materials and they count toward the same tiers.
If you just want the five CMYKW colors, the FullSpectrum CMYKW 5-Pack puts cyan, magenta, yellow, white and black in one order for $109.95.
Once our H3C is running, I'll share what we print with this set. If you print something with it first, send it our way. I'd love to see it.
Shop the CMYKW 5-Pack · Cyan · Magenta · Yellow · White · Black · Transparent Smoke Black
Happy Printing!
- John
0 comments